 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ericsson internal product specification 1 (4) prepared (also subject responsible if other) no. ebozhao 1/1301-bmr656 8118 approved checked date rev reference sec/d (julia you) 2011-10-18 c key features ? industry standard pola tm compatible 34.8 x 15.75 x 8.5 mm (1. 37 x 0.62 x 0.335 in) ? high efficiency, up to 96% ? auto track tm sequencing pin ? turbo trans tm technology for ultra-fast transient ? mtbf 4.6 mh general characteristics ? operating temperat ure: -40oc to 85oc ? input under voltage protection ? start up into a pre-biased output ? output short-circuit protection ? on/off inhibit control ? wide input voltage function ? wide output voltage adjust function ? highly automated manufacturing ensures quality ? iso 9001/14001 certified supplier safety approvals design for environment meets requirements in high- temperature lead-free soldering processes. contents ordering info rmation .............................................................. 2 general info rmation .............................................................. 2 safety specif ication .............................................................. 3 absolute maximu m ratings .............................................................. 4 product program ordering no. 0.7?3.6v, 30a / 108w pmn 8118u w p ..................................... 0.7v, 30a / 21w electric al specification .............................................................. 5 1.0v, 30a / 30w electric al specification .............................................................. 8 1.2v, 30a / 36w electric al specific ation ............................................................ 11 1.5v, 30a / 45w electric al specific ation ............................................................ 14 1.8v, 30a / 54w electric al specific ation ............................................................ 17 2.5v, 30a / 75w electric al specific ation ............................................................ 20 3.3v, 30a / 99w electric al specific ation ............................................................ 23 emc specific ation ............................................................ 26 operating info rmation ............................................................ 26 thermal consi deratio n ............................................................ 30 connecti ons ............................................................ 31 mechanical in formati on ............................................................ 33 soldering info rmation ............................................................ 35 delivery info rmation ............................................................ 36 product qualification specificat ion ............................................................ 37 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation
ericsson internal product specification 2 (4) prepared (also subject responsible if other) no. ebozhao 1/1301-bmr656 8118 approved checked date rev reference sec/d (julia you) 2011-10-18 c ordering information product program output pmn 8118uw p 0.7-3.6 v, 30 a /108 w product number and packaging pmn 8118uw p n 1 n 2 options n 1 n 2 smd pin smd pin with lead-free surface options description n 1 n 2 p s sr through-hole * smd pin smd pin with lead-free surface example a smd pin with lead-free surface, pmn 8118uw sr * standard variant (i.e. no option selected). general information reliability the failure rate ( ) and mean time between failures (mtbf= 1/ ) is calculated at max output power and an operating ambient temperature (t a ) of +40c. ericsson power modules uses telcordia sr-332 issue 2 method 1 to calculate the mean steady-state failure rate and standard deviation ( ). telcordia sr-332 issue 2 also provides techniques to estimate the upper confidence levels of failure rates based on the mean and standard deviation. mean steady-state failure rate, std. deviation, 167 nfailures/h 41 nfailures/h mtbf (mean value) for the pmn series = 6 mh. mtbf at 90% confidence level = 4.6 mh compatibility with rohs requirements the products are compatible with the relevant clauses and requirements of the rohs di rective 2011/65/eu and have a maximum concentration value of 0.1% by weight in homogeneous materials for lead, mercury, hexavalent chromium, pbb and pbde and of 0.01% by weight in homogeneous materials for cadmium. exemptions in the rohs di rective utilized in ericsson power modules products are found in the statement of compliance document. ericsson power modules fulfills and will continuously fulfill all its obligations under regulation (ec) no 1907/2006 concerning the registration, evaluation, authorization and restriction of chemicals (reach) as they enter into force and is through product materials declarations preparing for the obligations to communicate information on substances in the products. quality statement the products are designed and manufactured in an industrial environment where quality systems and methods like iso 9000, six sigma, and spc are intensively in use to boost the continuous improv ements strategy. infant mortality or early failures in the products are screened out and they are subjected to an ate-based final test. conservative design rules, design reviews and product qualifications, plus the high competence of an engaged work force, contribute to the high quality of the products. warranty warranty period and conditions are defined in ericsson power modules general terms and conditions of sale. limitation of liability ericsson power modules does not make any other warranties, expressed or implied including any warranty of merchantability or fitness for a particular purpose (including, but not limited to, use in life support applications, where malfuncti ons of product can cause injury to a person?s health or life). ? ericsson ab 2011 the information and specifications in this technical specification is believed to be correct at the time of publication. however, no liability is accepted for inaccuracies, printing errors or for any consequences thereof. ericsson ab reserves the right to change the contents of this technical spec ification at any time without prior notice. e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 2 ericsson internal product specification 3 (4) prepared (also subject responsible if other) no. ebozhao 1/1301-bmr656 8118 approved checked date rev reference sec/d (julia you) 2011-10-18 c safety specification general information ericsson power modules dc/dc converters and dc/dc regulators are designed in accordance with the safety standards iec 60950-1, en 60950-1 and ul 60950-1 safety of information technology equipment . iec/en/ul 60950-1 contains requirements to prevent injury or damage due to the following hazards: ? electrical shock ? energy hazards ? fire ? mechanical and heat hazards ? radiation hazards ? chemical hazards on-board dc/dc converters and dc/dc regulators are defined as component power supplies. as components they cannot fully comply with the provisions of any safety requirements without ?conditions of acceptability?. clearance between conductors and between conductive parts of the component power supply and conductors on the board in the final product must meet the applicable safety requirements. certain conditions of acceptability apply for component power supplies with limited stand-off (see mechanical information for further information). it is the responsibility of the insta ller to ensure that the final product housing these components complies with the requirements of all applicable safety standards and regulations for the final product. component power supplies for general use should comply with the requirements in iec/en/ul 60950-1 safety of information technology equipment. product related standards, e.g. ieee 802.3af power over ethernet , and ets-300132-2 power interface at t he input to telecom equipment, operated by direct current (dc) are based on iec/en/ul 60950-1 with regards to safety. ericsson power modules dc/dc converters and dc/dc regulators are ul 60950-1 recognized and certified in accordance with en 60950-1. the flammability rating for all construction parts of the pr oducts meet requirements for v-0 class material according to iec 60695-11-10, fire hazard testing, test flames ? 50 w horizontal and vertical flame test methods. isolated dc/dc converters galvanic isolation between input and output is verified in an electric strength test and the isolation voltage (v iso ) meets the voltage strength requir ement for basic insulation according to iec/en/ul 60950-1. it is recommended to use a slow blow fuse at the input of each dc/dc converter. if an input filter is used in the circuit the fuse should be placed in front of the input filter. in the rare event of a component problem that imposes a short circuit on the input source, this fuse will provide the following functions: ? isolate the fault from the input power source so as not to affect the operation of other parts of the system ? protect the distribution wi ring from excessive current and power loss thus preventing hazardous overheating the dc/dc converter output is considered as safety extra low voltage (selv) if one of the following conditions is met: ? the input source has double or reinforced insulation from the ac mains according to iec/en/ul 60950-1 ? the input source has basic or supplementary insulation from the ac mains and the input of the dc/dc converter is maximum 60 vdc and connected to protective earth according to iec/en/ul 60950-1 ? the input source has basic or supplementary insulation from the ac mains and the dc/dc converter output is connected to protective earth according to iec/en/ul 60950-1 non-isolated dc/dc regulators the dc/dc regulator output is selv if the input source meets the requirements for selv circuits according to iec/en/ul 60950-1. e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 3 ericsson internal product specification 1 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e absolute maximum ratings characteristics min typ max unit t ref operating temperature (see thermal consideration section) ?40 85 c t s storage temperature ?40 125 c v i input voltage 5.5 12 14 v positive logic option v in -0.5 open v v rc remote control pin voltage (see operating information section) negative logic option n/a n/a v v adj adjust pin voltage (see operating information section) n/a n/a v stress in excess of absolute maximum ratings may cause permanent damage. absolute maximum ratings, sometimes referred to as no destruction limits, are normally tested with one parameter at a time exceeding the limits of output data or electrical characteristics. if exposed to s tress above these limits, function and performance may degrade in an unspecified manner. fundamental circuit diagram 1 3 2 1 3 2 1 2 pwm controller error amplifier rc block auto track gnd ref inh/uvlo vin gnd gnd vout adj trk -vsen turbo trans +vsen uvlo prog block gnd turbo trans e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 4 ericsson internal product specification 2 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 0.7v, 30a / 21w electrical specification pmn 8118uw p t ref = -40 to +85oc, v i = 5.5 to 14 v, r adj = open, unless otherwise specified under conditions. typical values given at: t ref = +25c, v i = 12 v, max i o , unless otherwise specified under conditions. additional c in = 470 f and c out = 470 f. see operating information sect ion for selection of capacitor types. connect the sense pin, where available, to the output pin. characteristics conditions min typ max unit v i input voltage range 5.5 12 14 v v ioff turn-off input voltage decreasing input voltage 3.9 4.2 v v ion turn-on input voltage increasing input voltage 5.1 5.3 v c i internal input capacitance 44 f p o output power 0 21 w 50 % of max i o 84.7 efficiency max i o 79.3 % p d power dissipation max i o 5.5 6 w p li input idling power i o = 0 a, v i = 12 v 0.5 w p rc input standby power v i = 12 v (turned off with rc) 33.9 mw i s static input current v i = 12 v, max i o 2.2 a f s switching frequency 0-100 % of max i o 430 480 530 khz v oi output voltage initial setting and accuracy t ref = +25c, v i = 12 v, max i o 0.689 0.700 0.711 v output voltage tolerance band 10-100 % of max i o 0.679 0.721 v idling voltage i o = 0 a 0.703 v line regulation max i o 4 mv v o load regulation v i = 12 v, 0-100 % of max i o 7 mv v tr load transient voltage deviation 130 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s without turbo trans c o =1000 f type a 50 s v tr load transient voltage deviation 95 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s with turbo trans c o =1000 f type a; r tt =20 k 40 s t r ramp-up time (from 10 ? 90 % of v oi ) 9.9 ms t s start-up time (from v i connection to 90 % of v oi ) 100 % of max i o 16.8 ms max i o 1.4 m s t f v i shut-down fall time. (from v i off to 10 % of v o ) i o = 0.1 a 93.6 ms rc start-up time max i o 15.9 ms max i o 0.2 ms t rc t inh rc shut-down fall time (from rc off to 10 % of v o ) i o = 0.1 a 0.3 ms i o output current 0 30 a i lim current limit threshold t ref < max t ref 58 a i sc short circuit current t ref = 25oc, 58 a v oac output ripple & noise see ripple & noise section, max i o 5.7 mvp-p e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 5 ericsson internal product specification 3 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 0.7v, 30a / 21w typical characteristics pmn 8118uw p efficiency power dissipation 70 75 80 85 90 95 0 5 10 15 20 25 30 [a] [%] 5.5 v 12 v 14v 0 2 4 6 8 0 5 10 15 20 25 30 [a] [w] 5.5 v 12 v 14 v efficiency vs. load current and input voltage at t ref = +25 c dissipated power vs. load current and input voltage at t ref = +25c output current derating thermal resistance 0 10 20 30 40 20 30 40 50 60 70 80 90 [c] [a] 2.0 m/s 1.0 m/s 0.5 m/s nat. conv. 6 8 10 12 14 16 0.0 0.4 0.8 1.2 1.6 2.0[m/s] [c/w] available load current vs. ambient air temperature and airflow at v i = 12 v. see thermal consideration section. thermal resistance vs. airspeed measured at the converter. tested in wind tunnel with airflow and test conditions as per the thermal consideration section. output characteristics current limit characteristics 0.699 0.701 0.703 0.705 0.707 0 5 10 15 20 25 30 [a] [v] 5.5 v 12 v 14 v 0.00 0.20 0.40 0.60 0.80 40 45 50 55 60 65 70 [a] [v] 5.5 v 12 v 14 v o utput voltage vs. load current at t ref = +25c o utput voltage vs. load current at i o > max i o , t ref = +25c e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 6 ericsson internal product specification 4 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 0.7v, 30a / 21w typical characteristics pmn 8118uw p start-up shut-down start-up enabled by connecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (5 ms/div.). shut-down enabled by disconnecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (0.5 ms/div.). output ripple & noise output load transient response with turbo trans without turbo trans with turbo trans without turbo trans output voltage ripple at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. trace: output voltage (5 mv/div.). time scale: (2 s/div.). output voltage response to load current step- change (7.5-22.5-7.5 a) at: t ref =+25c, v i = 12 v. top trace: output voltage (100 mv/div.). middle trace: output voltage (100mv/div.). bottom trace: load current (20 a/div.). time scale: (0.1 ms/div.). output voltage adjust (see operating information) passive adjust the resistor value for an adjusted output voltage is calculated by using the equations in the operating information. ? ? = k v k r o set 49.6 7.0 7.0 1.30 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 7 ericsson internal product specification 5 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.0v, 30a / 30w electrical specification pmn 8118uw p t ref = -40 to +85oc, v i = 5.5 to 14 v, r adj = 63.4 k , unless otherwise specified under conditions. typical values given at: t ref = +25c, v i = 12 v, max i o , unless otherwise specified under conditions. additional c in = 470 f and c out = 470 f. see operating information sect ion for selection of capacitor types. connect the sense pin, where available, to the output pin. characteristics conditions min typ max unit v i input voltage range 5.5 12 14 v v ioff turn-off input voltage decreasing input voltage 3.9 4.2 v v ion turn-on input voltage increasing input voltage 5.1 5.3 v c i internal input capacitance 44 f p o output power 0 30 w 50 % of max i o 87.7 efficiency max i o 83.9 % p d power dissipation max i o 5.8 6.3 w p li input idling power i o = 0 a, v i = 12 v 0.67 w p rc input standby power v i = 12 v (turned off with rc) 30.2 mw i s static input current v i = 12 v, max i o 3.0 a f s switching frequency 0-100 % of max i o 430 480 530 khz v oi output voltage initial setting and accuracy t ref = +25c, v i = 12 v, max i o 0.985 1.000 1.015 v output voltage tolerance band 10-100 % of max i o 0.970 1.030 v idling voltage i o = 0 a 1.006 v line regulation max i o 4 mv v o load regulation v i = 12 v, 0-100 % of max i o 7 mv v tr load transient voltage deviation 130 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s without turbo trans c o =1000 f type a 50 s v tr load transient voltage deviation 90 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s with turbo trans c o =1000 f type a; r tt =20 k 40 s t r ramp-up time (from 10 ? 90 % of v oi ) 9.5 ms t s start-up time (from v i connection to 90 % of v oi ) 100 % of max i o 15.0 ms max i o 1.1 m s t f v i shut-down fall time. (from v i off to 10 % of v o ) i o = 0.1 a 73.1 ms rc start-up time max i o 16.0 ms max i o 0.2 ms t rc t inh rc shut-down fall time (from rc off to 10 % of v o ) i o = 0.1 a 0.3 ms i o output current 0 30 a i lim current limit threshold t ref < max t ref 58 a i sc short circuit current t ref = 25oc, 58 a v oac output ripple & noise see ripple & noise section, max i o 7.8 mvp-p e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 8 ericsson internal product specification 6 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.0v, 30a / 30w typical characteristics pmn 8118uw p efficiency power dissipation 70 75 80 85 90 95 0 5 10 15 20 25 30 [a] [%] 5.5 v 12 v 14v 0 2 4 6 8 0 5 10 15 20 25 30 [a] [w] 5.5 v 12 v 14 v efficiency vs. load current and input voltage at t ref = +25 c dissipated power vs. load current and input voltage at t ref = +25c output current derating thermal resistance 0 10 20 30 40 20 30 40 50 60 70 80 90 [c] [a] 2.0 m/s 1.0 m/s 0.5 m/s nat. conv. 6 8 10 12 14 16 0.0 0.4 0.8 1.2 1.6 2.0[m/s] [c/w] available load current vs. ambient air temperature and airflow at v i = 12 v. see thermal consideration section. thermal resistance vs. airspeed measured at the converter. tested in wind tunnel with airflow and test conditions as per the thermal consideration section. output characteristics current limit characteristics 1.000 1.002 1.004 1.006 1.008 0 5 10 15 20 25 30 [a] [v] 5.5 v 12 v 14 v 0.00 0.30 0.60 0.90 1.20 40 45 50 55 60 65 70 [a] [v] 5.5 v 12 v 14 v o utput voltage vs. load current at t ref = +25c o utput voltage vs. load current at i o > max i o , t ref = +25c e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 9 ericsson internal product specification 7 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.0v, 30a / 30w typical characteristics pmn 8118uw p start-up shut-down start-up enabled by connecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (5 ms/div.). shut-down enabled by disconnecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (0.5 ms/div.). output ripple & noise output load transient response with turbo trans without turbo trans with turbo trans without turbo trans output voltage ripple at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. trace: output voltage (5 mv/div.). time scale: (2 s/div.). output voltage response to load current step- change (7.5-22.5-7.5 a) at: t ref =+25c, v i = 12 v. top trace: output voltage (100 mv/div.). middle trace: output voltage (100 mv/div.). bottom trace: load current (20 a/div.). time scale: (0.1 ms/div.). output voltage adjust (see operating information) passive adjust the resistor value for an adjusted output voltage is calculated by using the equations in the operating information. ? ? = k v k r o set 49.6 7.0 7.0 1.30 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 10 ericsson internal product specification 8 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.2v, 30a / 36w electrical specification pmn 8118uw p t ref = -40 to +85oc, v i = 5.5 to 14 v, r adj = 35.7 k , unless otherwise specified under conditions. typical values given at: t ref = +25c, v i = 12 v, max i o , unless otherwise specified under conditions. additional c in = 470 f and c out = 470 f. see operating information sect ion for selection of capacitor types. connect the sense pin, where available, to the output pin. characteristics conditions min typ max unit v i input voltage range 5.5 12 14 v v ioff turn-off input voltage decreasing input voltage 3.9 4.2 v v ion turn-on input voltage increasing input voltage 5.1 5.3 v c i internal input capacitance 44 f p o output power 0 36 w 50 % of max i o 88.9 efficiency max i o 85.8 % p d power dissipation max i o 6 6.5 w p li input idling power i o = 0 a, v i = 12 v 0.83 w p rc input standby power v i = 12 v (turned off with rc) 26.4 mw i s static input current v i = 12 v, max i o 3.52 a f s switching frequency 0-100 % of max i o 430 480 530 khz v oi output voltage initial setting and accuracy t ref = +25c, v i = 12 v, max i o 1.182 1.200 1.218 v output voltage tolerance band 10-100 % of max i o 1.164 1.236 v idling voltage i o = 0 a 1.206 v line regulation max i o 4 mv v o load regulation v i = 12 v, 0-100 % of max i o 7 mv v tr load transient voltage deviation 130 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s without turbo trans c o =1000 f type a 50 s v tr load transient voltage deviation 90 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s with turbo trans c o =1000 f type a; r tt =20 k 50 s t r ramp-up time (from 10 ? 90 % of v oi ) 9.2 ms t s start-up time (from v i connection to 90 % of v oi ) 100 % of max i o 14.6 ms max i o 1.0 m s t f v i shut-down fall time. (from v i off to 10 % of v o ) i o = 0.1 a 67.8 ms rc start-up time max i o 16.0 ms max i o 0.2 ms t rc t inh rc shut-down fall time (from rc off to 10 % of v o ) i o = 0.1 a 0.3 ms i o output current 0 30 a i lim current limit threshold t ref < max t ref 58 a i sc short circuit current t ref = 25oc, 58 a v oac output ripple & noise see ripple & noise section, max i o 8.8 mvp-p e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 11 ericsson internal product specification 9 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.2v, 30a / 36w typical characteristics pmn 8118uw p efficiency power dissipation 70 75 80 85 90 95 0 5 10 15 20 25 30 [a] [%] 5.5 v 12 v 14v 0 2 4 6 8 0 5 10 15 20 25 30 [a] [w] 5.5 v 12 v 14 v efficiency vs. load current and input voltage at t ref = +25 c dissipated power vs. load current and input voltage at t ref = +25c output current derating thermal resistance 0 10 20 30 40 20 30 40 50 60 70 80 90 [c] [a] 2.0 m/s 1.0 m/s 0.5 m/s nat. conv. 6 8 10 12 14 16 0.0 0.4 0.8 1.2 1.6 2.0[m/s] [c/w] available load current vs. ambient air temperature and airflow at v i = 12 v. see thermal consideration section. thermal resistance vs. airspeed measured at the converter. tested in wind tunnel with airflow and test conditions as per the thermal consideration section. output characteristics current limit characteristics 1.200 1.202 1.204 1.206 1.208 0 5 10 15 20 25 30 [a] [v] 5.5 v 12 v 14 v 0.00 0.30 0.60 0.90 1.20 1.50 40 45 50 55 60 65 70 [a] [v] 5.5 v 12 v 14 v o utput voltage vs. load current at t ref = +25c o utput voltage vs. load current at i o > max i o , t ref = +25c e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 12 ericsson internal product specification 10 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.2v, 30a / 36w typical characteristics pmn 8118uw p start-up shut-down start-up enabled by connecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (5 ms/div.). shut-down enabled by disconnecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (0.5 ms/div.). output ripple & noise output load transient response with turbo trans without turbo trans with turbo trans without turbo trans output voltage ripple at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. trace: output voltage (5 mv/div.). time scale: (2 s/div.). output voltage response to load current step- change (7.5-22.5-7.5 a) at: t ref =+25c, v i = 12 v. top trace: output voltage (100 mv/div.). middle trace: output voltage (100 mv/div.). bottom trace: load current (20 a/div.). time scale: (0.1 ms/div.). output voltage adjust (see operating information) passive adjust the resistor value for an adjusted output voltage is calculated by using the equations in the operating information. ? ? = k v k r o set 49.6 7.0 7.0 1.30 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 13 ericsson internal product specification 11 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.5v, 30a / 45w electrical specification pmn 8118uw p t ref = -40 to +85oc, v i = 5.5 to 14 v, r adj = 19.6 k , unless otherwise specified under conditions. typical values given at: t ref = +25c, v i = 12 v, max i o , unless otherwise specified under conditions. additional c in = 470 f and c out = 470 f. see operating information sect ion for selection of capacitor types. connect the sense pin, where available, to the output pin. characteristics conditions min typ max unit v i input voltage range 5.5 12 14 v v ioff turn-off input voltage decreasing input voltage 3.9 4.2 v v ion turn-on input voltage increasing input voltage 5.1 5.3 v c i internal input capacitance 44 f p o output power 0 45 w 50 % of max i o 90.1 efficiency max i o 87.9 % p d power dissipation max i o 6.2 6.7 w p li input idling power i o = 0 a, v i = 12 v 1.06 w p rc input standby power v i = 12 v (turned off with rc) 26.4 mw i s static input current v i = 12 v, max i o 4.32 a f s switching frequency 0-100 % of max i o 430 480 530 khz v oi output voltage initial setting and accuracy t ref = +25c, v i = 12 v, max i o 1.477 1.500 1.523 v output voltage tolerance band 10-100 % of max i o 1.455 1.545 v idling voltage i o = 0 a 1.513 v line regulation max i o 4 mv v o load regulation v i = 12 v, 0-100 % of max i o 7 mv v tr load transient voltage deviation 130 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s without turbo trans c o =1000 f type a 60 s v tr load transient voltage deviation 90 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s with turbo trans c o =1000 f type a; r tt =20 k 40 s t r ramp-up time (from 10 ? 90 % of v oi ) 9.7 ms t s start-up time (from v i connection to 90 % of v oi ) 100 % of max i o 15.4 ms max i o 0.9 m s t f v i shut-down fall time. (from v i off to 10 % of v o ) i o = 0.1 a 61.4 ms rc start-up time max i o 16.4 ms max i o 0.2 ms t rc t inh rc shut-down fall time (from rc off to 10 % of v o ) i o = 0.1 a 0.3 ms i o output current 0 30 a i lim current limit threshold t ref < max t ref 58 a i sc short circuit current t ref = 25oc, 58 a v oac output ripple & noise see ripple & noise section, max i o 9.9 mvp-p e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 14 ericsson internal product specification 12 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.5v, 30a / 45w typical characteristics pmn 8118uw p efficiency power dissipation 70 75 80 85 90 95 0 5 10 15 20 25 30 [a] [%] 5.5 v 12 v 14v 0 2 4 6 8 0 5 10 15 20 25 30 [a] [w] 5.5 v 12 v 14 v efficiency vs. load current and input voltage at t ref = +25 c dissipated power vs. load current and input voltage at t ref = +25c output current derating thermal resistance 0 10 20 30 40 20 30 40 50 60 70 80 90 [c] [a] 2.0 m/s 1.0 m/s 0.5 m/s nat. conv. 6 8 10 12 14 16 0.0 0.4 0.8 1.2 1.6 2.0[m/s] [c/w] available load current vs. ambient air temperature and airflow at v i = 12 v. see thermal consideration section. thermal resistance vs. airspeed measured at the converter. tested in wind tunnel with airflow and test conditions as per the thermal consideration section. output characteristics current limit characteristics 1.508 1.510 1.512 1.514 1.516 0 5 10 15 20 25 30 [a] [v] 5.5 v 12 v 14 v 0.10 0.40 0.70 1.00 1.30 1.60 40 45 50 55 60 65 70 [a] [v] 5.5 v 12 v 14 v o utput voltage vs. load current at t ref = +25c o utput voltage vs. load current at i o > max i o , t ref = +25c e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 15 ericsson internal product specification 13 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.5v, 30a / 45w typical characteristics pmn 8118uw p start-up shut-down start-up enabled by connecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (5 ms/div.). shut-down enabled by disconnecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (0.5 ms/div.). output ripple & noise output load transient response with turbo trans without turbo trans with turbo trans without turbo trans output voltage ripple at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. trace: output voltage (5 mv/div.). time scale: (2 s/div.). output voltage response to load current step- change (7.5-22.5-7.5 a) at: t ref =+25c, v i = 12 v. top trace: output voltage (100 mv/div.). middle trace: output voltage (100 mv/div.). bottom trace: load current (20 a/div.). time scale: (0.1 ms/div.). output voltage adjust (see operating information) passive adjust the resistor value for an adjusted output voltage is calculated by using the equations in the operating information. ? ? = k v k r o set 49.6 7.0 7.0 1.30 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 16 ericsson internal product specification 14 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.8v, 30a / 54w electrical specification pmn 8118uw p t ref = -40 to +85oc, v i = 5.5 to 14 v, r adj = 12.7 k , unless otherwise specified under conditions. typical values given at: t ref = +25c, v i = 12 v, max i o , unless otherwise specified under conditions. additional c in = 470 f and c out = 470 f. see operating information sect ion for selection of capacitor types. connect the sense pin, where available, to the output pin. characteristics conditions min typ max unit v i input voltage range 5.5 12 14 v v ioff turn-off input voltage decreasing input voltage 3.9 4.2 v v ion turn-on input voltage increasing input voltage 5.1 5.3 v c i internal input capacitance 44 f p o output power 0 54 w 50 % of max i o 90.8 efficiency max i o 89.2 % p d power dissipation max i o 6.5 7.0 w p li input idling power i o = 0 a, v i = 12 v 1.32 w p rc input standby power v i = 12 v (turned off with rc) 18.8 mw i s static input current v i = 12 v, max i o 5.00 a f s switching frequency 0-100 % of max i o 430 480 530 khz v oi output voltage initial setting and accuracy t ref = +25c, v i = 12 v, max i o 1.773 1.800 1.827 v output voltage tolerance band 10-100 % of max i o 1.746 1.854 v idling voltage i o = 0 a 1.795 v line regulation max i o 4 mv v o load regulation v i = 12 v, 0-100 % of max i o 7 mv v tr load transient voltage deviation 130 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s without turbo trans c o =1000 f type a 60 s v tr load transient voltage deviation 90 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s with turbo trans c o =1000 f type a; r tt =20 k 40 s t r ramp-up time (from 10 ? 90 % of v oi ) 10.2 ms t s start-up time (from v i connection to 90 % of v oi ) 100 % of max i o 16.1 ms max i o 0.9 m s t f v i shut-down fall time. (from v i off to 10 % of v o ) i o = 0.1 a 60.3 ms rc start-up time max i o 16.5 ms max i o 0.3 ms t rc t inh rc shut-down fall time (from rc off to 10 % of v o ) i o = 0.1 a 0.4 ms i o output current 0 30 a i lim current limit threshold t ref < max t ref 56 a i sc short circuit current t ref = 25oc, 56 a v oac output ripple & noise see ripple & noise section, max i o 11.9 mvp-p e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 17 ericsson internal product specification 15 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.8v, 30a / 54w typical characteristics pmn 8118uw p efficiency power dissipation 70 75 80 85 90 95 0 5 10 15 20 25 30 [a] [%] 5.5 v 12 v 14v 0 2 4 6 8 0 5 10 15 20 25 30 [a] [w] 5.5 v 12 v 14 v efficiency vs. load current and input voltage at t ref = +25 c dissipated power vs. load current and input voltage at t ref = +25c output current derating thermal resistance 0 10 20 30 40 20 30 40 50 60 70 80 90 [c] [a] 2.0 m/s 1.0 m/s 0.5 m/s nat. conv. 7 9 11 13 15 0.0 0.4 0.8 1.2 1.6 2.0[m/s] [c/w] available load current vs. ambient air temperature and airflow at v i = 12 v. see thermal consideration section. thermal resistance vs. airspeed measured at the converter. tested in wind tunnel with airflow and test conditions as per the thermal consideration section. output characteristics current limit characteristics 1.787 1.789 1.791 1.793 1.795 0 5 10 15 20 25 30 [a] [v] 5.5 v 12 v 14 v 0.00 0.40 0.80 1.20 1.60 2.00 40 45 50 55 60 65 70 [a] [v] 5.5 v 12 v 14 v o utput voltage vs. load current at t ref = +25c o utput voltage vs. load current at i o > max i o , t ref = +25c e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 18 ericsson internal product specification 16 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 1.8v, 30a / 54w typical characteristics pmn 8118uw p start-up shut-down start-up enabled by connecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (5 ms/div.). shut-down enabled by disconnecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (0.5 ms/div.). output ripple & noise output load transient response with turbo trans without turbo trans with turbo trans without turbo trans output voltage ripple at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. trace: output voltage (5 mv/div.). time scale: (2 s/div.). output voltage response to load current step- change (7.5-22.5-7.5 a) at: t ref =+25c, v i = 12 v. top trace: output voltage (100 mv/div.). middle trace: output voltage (100 mv/div.). bottom trace: load current (20 a/div.). time scale: (0.1 ms/div.). output voltage adjust (see operating information) passive adjust the resistor value for an adjusted output voltage is calculated by using the equations in the operating information. ? ? = k v k r o set 49.6 7.0 7.0 1.30 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 19 ericsson internal product specification 17 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 2.5v, 30a / 75w electrical specification pmn 8118uw p t ref = -40 to +85oc, v i = 5.5 to 14 v, r adj = 5.23 k , unless otherwise specified under conditions. typical values given at: t ref = +25c, v i = 12 v, max i o , unless otherwise specified under conditions. additional c in = 470 f and c out = 470 f. see operating information sect ion for selection of capacitor types. connect the sense pin, where available, to the output pin. characteristics conditions min typ max unit v i input voltage range 5.5 12 14 v v ioff turn-off input voltage decreasing input voltage 3.9 4.2 v v ion turn-on input voltage increasing input voltage 5.1 5.3 v c i internal input capacitance 44 f p o output power 0 75 w 50 % of max i o 91.9 efficiency max i o 91.3 % p d power dissipation max i o 7.2 7.7 w p li input idling power i o = 0 a, v i = 12 v 1.96 w p rc input standby power v i = 12 v (turned off with rc) 26.4 mw i s static input current v i = 12 v, max i o 6.90 a f s switching frequency 0-100 % of max i o 430 480 530 khz v oi output voltage initial setting and accuracy t ref = +25c, v i = 12 v, max i o 2.462 2.500 2.538 v output voltage tolerance band 10-100 % of max i o 2.425 2.575 v idling voltage i o = 0 a 2.508 v line regulation max i o 4 mv v o load regulation v i = 12 v, 0-100 % of max i o 7 mv v tr load transient voltage deviation 130 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s without turbo trans c o =1000 f type a 60 s v tr load transient voltage deviation 90 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s with turbo trans c o =1000 f type a; r tt =20 k 40 s t r ramp-up time (from 10 ? 90 % of v oi ) 11.0 ms t s start-up time (from v i connection to 90 % of v oi ) 100 % of max i o 16.2 ms max i o 0.8 m s t f v i shut-down fall time. (from v i off to 10 % of v o ) i o = 0.1 a 61.4 ms rc start-up time max i o 15.4 ms max i o 0.3 ms t rc t inh rc shut-down fall time (from rc off to 10 % of v o ) i o = 0.1 a 0.4 ms i o output current 0 30 a i lim current limit threshold t ref < max t ref 56 a i sc short circuit current t ref = 25oc, 56 a v oac output ripple & noise see ripple & noise section, max i o 12.6 mvp-p e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 20 ericsson internal product specification 18 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 2.5v, 30a / 75w typical characteristics pmn 8118uw p efficiency power dissipation 72 77 82 87 92 97 0 5 10 15 20 25 30 [a] [%] 5.5 v 12 v 14v 0 2 4 6 8 0 5 10 15 20 25 30 [a] [w] 5.5 v 12 v 14 v efficiency vs. load current and input voltage at t ref = +25 c dissipated power vs. load current and input voltage at t ref = +25c output current derating thermal resistance 0 10 20 30 40 20 30 40 50 60 70 80 90 [c] [a] 2.0 m/s 1.0 m/s 0.5 m/s nat. conv. 7 9 11 13 15 0.0 0.4 0.8 1.2 1.6 2.0[m/s] [c/w] available load current vs. ambient air temperature and airflow at v i = 12 v. see thermal consideration section. thermal resistance vs. airspeed measured at the converter. tested in wind tunnel with airflow and test conditions as per the thermal consideration section. output characteristics current limit characteristics 2.502 2.504 2.506 2.508 2.510 0 5 10 15 20 25 30 [a] [v] 5.5 v 12 v 14 v 0.00 0.50 1.00 1.50 2.00 2.50 3.00 40 45 50 55 60 65 70 [a] [v] 5.5 v 12 v 14 v o utput voltage vs. load current at t ref = +25c o utput voltage vs. load current at i o > max i o , t ref = +25c e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 21 ericsson internal product specification 19 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 2.5v, 30a / 75w typical characteristics pmn 8118uw p start-up shut-down start-up enabled by connecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (5 ms/div.). shut-down enabled by disconnecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (0.5 ms/div.). output ripple & noise output load transient response with turbo trans without turbo trans with turbo trans without turbo trans output voltage ripple at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. trace: output voltage (5 mv/div.). time scale: (2 s/div.). output voltage response to load current step- change (7.5-22.5-7.5 a) at: t ref =+25c, v i = 12 v. top trace: output voltage (100 mv/div.). middle trace: output voltage (100 mv/div.). bottom trace: load current (20 a/div.). time scale: (0.1 ms/div.). output voltage adjust (see operating information) passive adjust the resistor value for an adjusted output voltage is calculated by using the equations in the operating information. ? ? = k v k r o set 49.6 7.0 7.0 1.30 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 22 ericsson internal product specification 20 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 3.3v, 30a / 99w electrical specification pmn 8118uw p t ref = -40 to +85oc, v i = 5.5 to 14 v, r adj = 1.62 k , unless otherwise specified under conditions. typical values given at: t ref = +25c, v i = 12 v, max i o , unless otherwise specified under conditions. additional c in = 470 f and c out = 470 f. see operating information sect ion for selection of capacitor types. connect the sense pin, where available, to the output pin. characteristics conditions min typ max unit v i input voltage range 5.5 12 14 v v ioff turn-off input voltage decreasing input voltage 3.9 4.2 v v ion turn-on input voltage increasing input voltage 5.1 5.3 v c i internal input capacitance 44 f p o output power 0 99 w 50 % of max i o 92.5 efficiency max i o 92.6 % p d power dissipation max i o 8.0 8.5 w p li input idling power i o = 0 a, v i = 12 v 2.64 w p rc input standby power v i = 12 v (turned off with rc) 18.8 mw i s static input current v i = 12 v, max i o 9.00 a f s switching frequency 0-100 % of max i o 430 480 530 khz v oi output voltage initial setting and accuracy t ref = +25c, v i = 12 v, max i o 3.250 3.300 3.350 v output voltage tolerance band 10-100 % of max i o 3.201 3.399 v idling voltage i o = 0 a 3.312 v line regulation max i o 4 mv v o load regulation v i = 12 v, 0-100 % of max i o 7 mv v tr load transient voltage deviation 130 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s without turbo trans c o =1000 f type a 60 s v tr load transient voltage deviation 90 mv t tr load transient recovery time v i = 12 v, load step 25-75-25 % of max i o , di/dt = 2.5 a/ s with turbo trans c o =1000 f type a; r tt =20 k 40 s t r ramp-up time (from 10 ? 90 % of v oi ) 11.1 ms t s start-up time (from v i connection to 90 % of v oi ) 100 % of max i o 16.4 ms max i o 0.8 m s t f v i shut-down fall time. (from v i off to 10 % of v o ) i o = 0.1 a 67.7 ms rc start-up time max i o 16.1 ms max i o 0.3 ms t rc t inh rc shut-down fall time (from rc off to 10 % of v o ) i o = 0.1 a 0.4 ms i o output current 0 30 a i lim current limit threshold t ref < max t ref 56 a i sc short circuit current t ref = 25oc, 56 a v oac output ripple & noise see ripple & noise section, max i o 14.5 mvp-p e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 23 ericsson internal product specification 21 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 3.3v, 30a / 99w typical characteristics pmn 8118uw p efficiency power dissipation 75 80 85 90 95 100 0 5 10 15 20 25 30 [a] [%] 5.5 v 12 v 14v 0 2 4 6 8 10 0 5 10 15 20 25 30 [a] [w] 5.5 v 12 v 14 v efficiency vs. load current and input voltage at t ref = +25 c dissipated power vs. load current and input voltage at t ref = +25c output current derating thermal resistance 0 10 20 30 40 20 30 40 50 60 70 80 90 [c] [a] 2.0 m/s 1.0 m/s 0.5 m/s nat. conv. 7 9 11 13 15 0.0 0.4 0.8 1.2 1.6 2.0[m/s] [c/w] available load current vs. ambient air temperature and airflow at v i = 12 v. see thermal consideration section. thermal resistance vs. airspeed measured at the converter. tested in wind tunnel with airflow and test conditions as per the thermal consideration section. output characteristics current limit characteristics 3.304 3.306 3.308 3.310 3.312 3.314 0 5 10 15 20 25 30 [a] [v] 5.5 v 12 v 14 v 0.00 0.70 1.40 2.10 2.80 3.50 40 45 50 55 60 65 70 [a] [v] 5.5 v 12 v 14 v o utput voltage vs. load current at t ref = +25c o utput voltage vs. load current at i o > max i o , t ref = +25c e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 24 ericsson internal product specification 22 (23) prepared (also subject responsible if other) no. eguhail 2/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) 2011-10-18 e 3.3v, 30a / 99w typical characteristics pmn 8118uw p start-up shut-down start-up enabled by connecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (5 ms/div.). shut-down enabled by disconnecting v i at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. top trace: output voltage (1 v/div.). bottom trace: input voltage (10 v/div.). time scale: (0.5 ms/div.). output ripple & noise output load transient response with turbo trans without turbo trans with turbo trans without turbo trans output voltage ripple at: t ref = +25c, v i = 12 v, i o = 30 a resistive load. trace: output voltage (5 mv/div.). time scale: (2 s/div.). output voltage response to load current step- change (7.5-22.5-7.5 a) at: t ref =+25c, v i = 12 v. top trace: output voltage (100 mv/div.). middle trace: output voltage (100 mv/div.). bottom trace: load current (20 a/div.). time scale: (0.1 ms/div.). output voltage adjust (see operating information) passive adjust the resistor value for an adjusted output voltage is calculated by using the equations in the operating information. ? ? = k v k r o set 49.6 7.0 7.0 1.30 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 25 ericsson internal product specification 1 (8) prepared (also subject responsible if other) no. eguhail 3/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) ebozhao 2011-10-17 c emc specification conducted emi measured according to test set-up. the fundamental switching frequency is 480 khz for pmn 8118uw p @ v i = 12 v, max i o . conducted emi input terminal value (typ) tbd emi without filter tbd test set-up layout recommendation the radiated emi performance of the dc/dc regulator will depend on the pcb layout and ground layer design. it is also important to consider the stand-off of the dc/dc regulator. if a ground layer is used, it should be connected to the output of the dc/dc regulator and the equipment ground or chassis. a ground layer will increase the stray capacitance in the pcb and improve the high frequency emc performance. output ripple and noise output ripple and noise measured according to figure below. see design note 022 for detailed information. output ripple and noise test setup operating information extended information for pola products is found in application note 205. input voltage the input voltage range 5.5 to 14 vdc makes the product easy to use in intermediate bus applications when powered by a regulated bus converter. turn-off input voltage the dc/dc regulators monitor the input voltage and will turn on and turn off at predetermined levels. the minimum hysteresis between turn on and turn off input voltage is 0.1v. remote control (rc) inhibit the products are fitted with a remote control function referenced to positive logic. the rc function allows the regulator to be turned on/off by an external device like a semiconductor or mechanical switch. the rc pin has an internal pull up resistor to + in. the maximum required sink current is 1 ma. when the rc pin is left open, the voltage generated on the rc pin is 5.5 ? 14 v. the regulator will turn on when the input voltage is applied with the rc pin open. turn off is achieved by connecting the rc pin to the - in. to ensure safe turn off the voltage difference between rc pin and the - in pin shall be less than 1v. the regulator will restart automatically when this connection is opened. e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 26 ericsson internal product specification 2 (8) prepared (also subject responsible if other) no. eguhail 3/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) ebozhao 2011-10-17 c external ca p acitors input capacitors: the recommended input capacitors are determined by the 470 f minimum capacitance and 500 marms minimum ripple current rating. for high-performance/transient application, or wherever the input source performance is degraded, 1000 f of input capacitance is recommended. the additional input capacitance above the minimum level insures an optimized performance. output capacitors: the recommended output capacitance of 470 f will allow the module to meet its transient response specification as defined in the electrical specification. when using one or more non-ceramic capacitors, the calculated equivalent esr should be no lower than 4 m (7m using the manufacturer?s maximum esr for a single capacitor). turbo trans tm allows the designer to optimize the capacitance load according to the system transient design requirement. high quality, ultra-low esr capacitors are required to maximize turbo trans tm effectiveness. capacitors with a capacitance (f)esr (m ? ) 10,000 m ? f are required. required capacitor with turbo trans. see the turbo trans tm application information for capacitor selection. capacitor type group by esr (equivalent series resistance) type a = (100 ericsson internal product specification 3 (8) prepared (also subject responsible if other) no. eguhail 3/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) ebozhao 2011-10-17 c over temperature protection (otp) the regulators are protected fr om thermal overload by an internal over temperature shutdown circuit. when t ref as defined in thermal consideration section exceeds the otp threshold, the regulator will shut down. the dc/dc regulator will make contin uous attempts to start up (non-latching mode) and resume normal operation automatically when the temper ature has dropped >10c below the temperature threshold. over current protection (ocp) the regulators include current limit ing circuitry for protection at continuous overload. the output voltage will decrease towards zero for output currents in excess of max output current (max i o ). the regulator will resume normal operation after removal of the overload. the load distributio n should be designed for the maximum output short circuit current specified. soft-start power up from the moment a valid input vo ltage is applied, the soft-start control introduces a short time-delay (typically 5-10 ms) before allowing the output voltage to rise. the initial rise in input current when the input voltage first starts to rise is the charge current drawn by the input capacitors. power-up is complete within 15 ms. auto track? function auto track tm was designed to simplify the amount of circuitry required to make the output voltage from each module power up and power down in sequence. the sequencing of two or more supply voltages during power up is a common requirement for complex mixed-signal applications, that use dual-voltage vlsi ics such as dsps, micro-processors and asics. adjustable undervoltage lockout the regulators incorporate an input undervoltage lockout (uvlo). the uvlo feature pr events the operation of the module until there is a sufficient input voltage to produce a valid output voltage. this enables the module to provide a clean, monotonic powerup for the load circuit and also limit the magnitude of current drawn from regulator?s input source during the power-up sequence. the uvlo characteristic is defined by the on threshold (v thd ) voltage. below the on thresh old, the inhibit control is overridden, and the moudule does not produce an output. the hysterisis voltage, which is the difference oscillations, which can occur if the input voltage drops slightly when the modules begins to draw current from the input source. the uvlo feature of the pmn 8118uw p module allows for limited adjustment of the on threshold voltage. the adjustment is made via the inhi bit/uvlo prog control pin (pin 1) using a single resistor (see figure below). when pin 1 is left open, the on threshold voltage is intermally set to its default value. the on threshold has a nominal voltage of 5.0 v and a hysterisis of 900 mv. this ensur es that the module produces a regulated output when the minimum input voltage is applied. the on threshold might need to be increased if the module is powered from a tightly regulated 12 v bus. this allows the on threshold voltage to be set for a specified input voltage. adjusting the threshold voltag e prevents the module from operating if the input bus fails to completely rise to its specified regulation voltage. the below equation determines the value of r uvlo required to adjust v thd to a new value. the default value is 5 v and it may only be adjusted to a higher value. )( 100)1(9.24 ))1(9.24(2590 ?? ?? = k v v r thd thd uvlo the above table lists the stan dard resistor values for r uvlo for different values of the on threshold (v thd ) voltage. the figure of uvlo program resi stor placement is as follow. turbo trans tm technology turbo trans tm optimizes the transi ent response of the regulator with added external capacitance using a single external resistor. the benefits of this technology include: reduced output capacitance, minimized output voltage deviation following a load transient, and enhanced stability when using ultra-low esr output capacitors. the amout of output capacitance required to meet a target output voltage deviation, is reduded with turbo trans tm activated. likewise, for a given amout of output capacitance, with turbo trans tm engaged, the amplitude of the voltage deviation following a load transient is reduced. applic ations requiring tight transient voltage tolerances and minimized capacitor footprint area benefit from this technology. utilizing turbo trans tm requires connecting a resistor, r tt , between the +sense pin (pin 10) and the turbo trans tm pin (pin 13), the value of the resistor directly corresponds to the e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 28 ericsson internal product specification 4 (8) prepared (also subject responsible if other) no. eguhail 3/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) ebozhao 2011-10-17 c amount of output capacitance required. for the pmn 8118uw p, the minimum required capacitance is 470 f. when using turbo trans tm , capacitors with a capacitanceesr product below 10,000 fm ? are required. to see the benefit of turbo trans tm , follow the 5mv/a marking across to the ?without turbo trans tm ? plot. following that point down shows that more than 8,200 f of output capacitance is required to meet the same transient deviation limit. this is the benefit of turbo trans tm . a typical turbo trans tm application schematic is also shown. r tt resistor selection the turbo trans tm resistor value, r tt can be determined from the turbo trans tm programming equation, see the equation below. )( 1) 2350 (5 ) 2350 (1 40 ? ? = k c c r o o tt where c o is the total output capacitance in f. c o values greater than or equal to 2350 f require r tt to be a short, 0 ? . (the above equation results in a negative value for r tt when c o 2350 f) r tt resistor selection the turbo trans tm resistor value, r tt can be determined from the turbo trans tm programming equation, see the equation below. )( 1) 2350 (5 ) 2350 (1 40 ? ? = k c c r o o tt where c o is the total output capacitance in f. c o values greater than or equal to 2350 f require r tt to be a short, 0 ? . (the above equation results in a negative value for r tt when c o 2350 f) e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 29 ericsson internal product specification 5 (8) prepared (also subject responsible if other) no. eguhail 3/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) ebozhao 2011-10-17 c r tt resistor selection the turbo trans tm resistor value, r tt can be determined from the turbo trans tm programming equation, see the equation below. )( 1) 2350 (5 ) 2350 (1 40 ? ? = k c c r o o tt where c o is the total output capacitance in f. c o values greater than or equal to 2350 f require r tt to be a short, 0 ? . (the above equation results in a negative value for r tt when c o 2350 f) thermal consideration general the regulators are designed to operate in different thermal environments and sufficient cooling must be provided to ensure reliable operation. cooling is achieved mainly by conduction, from the pins to the host board, and convection, which is dependant on the airflow across the regulator. increased ai rflow enhances the cooling of the regulator. the output current derating grap h found in the output section for each model provides the available output current vs. ambient air temperature and air velocity at v in = 5 v. the dc/dc regulator is te sted on a 254 x 254 mm, 35 m (1 oz), 8-layer test board mounted vertically in a wind tunnel with a cross-section of 305 x 305 mm. proper cooling of the dc/dc regulator can be verified by measuring the temperature at positions p1, p2 and p3. the temperature at these positio ns should not exceed the max values provided in the table below. note that the max value is the absolute maximum rating (non destruction) and that the electrical output data is guaranteed up to ambient temperature +85c. see design note 019 for further information. position device designation max value p 1 pcb 130o c p 2 mosfet 130o c p 3 inductor t ref 130o c e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 30 ericsson internal product specification 6 (8) prepared (also subject responsible if other) no. eguhail 3/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) ebozhao 2011-10-17 c thermal consideration continued definition of reference temperature (t ref ) the reference temperature is us ed to monitor the temperature limits of the product. temperatures above maximum t ref are not allowed and may cause degradation or permanent damage to the product. t ref is also used to define the temperature range for normal operating conditions. t ref is defined by the design and used to guarantee safety margins, proper operation and high reliability of the module. ambient temperature calculation by using the thermal resistance the maximum allowed ambient temperature can be calculated. 1. the power loss is calculated by using the formula ((1/ ) - 1) output power = power losses (pd). = efficiency of regulator. e.g 89.5 % = 0.895 2. find the thermal resistance (r th) in the thermal resistance graph found in the output section for each model. calculate the temperature increase ( t). t = rth x pd 3. max allowed ambient temperature is: max tref - t. e.g pmn 8118uw p at 0m/s: 1. (( ) - 1) 99 w = 7.91 w 2. 7.91 w 13.5c/w = 106.8c 3. 130 c ? 106.8c = max ambient temperature is 23.2c the actual temperature will be dependent on several factors such as the pcb size, number of layers and direction of airflow. connections pin designation function 1 inhibit/ uvlo adjust the inhibit pin is an open-collector/drain, negative logic input that is referenced to gnd. applying a low level ground signal to this input disables the module?s output voltage. if the inhibit pin is left open-circuit, the module produces an output whenever a valid input source is applied. this input is not compatible with ttl logic devices and should not be tied v i or other voltage. this pin is also used for input undervoltage lockout (uvlo) programming. connecting a resistor from this pin to gnd (pin 3) allows the on threshold of the uvlo to be adjusted higher than the default value. 2 v i the positive input voltage power node to the module, which is referenced to common gnd. 3 gnd this is the common ground connection for the v i and v o power connections. it is also the 0 v dc reference for the control inputs. 4 gnd this is the common ground connection for the v i and v o power connections. it is also the 0 v dc reference for the control inputs. 5 v o the regulated positive power output with respect to the gnd. 6 v i the positive input voltage power node to the module, which is referenced to common gnd. 1 0.926 e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 31 ericsson internal product specification 7 (8) prepared (also subject responsible if other) no. eguhail 3/1301-bmr 656 8118 uen approved checked date rev reference sec/d (julia you) ebozhao 2011-10-17 c 7 gnd this is the common ground connection for the v i and v o power connections. it is also the 0 v dc reference for the control inputs. 8 gnd this is the common ground connection for the v i and v o power connections. it is also the 0 v dc reference for the control inputs. 9 v o the regulated positive power output with respect to the gnd. 10 +sense the sense input allows the regulation circuit to compensate for voltage drop between the module and the load. for optimal voltage accuracy, +sense must be connect v o , very close to the load. 11 -sense the sense input allows the regulation circuit to compensate for voltage drop between the module and the load. for optimal voltage accu racy, -sense must be connect gnd(pin 8) , very close to the load. 12 v o adjust a 0.1 w 1% resistor must be directly connected between this pin and pin 8 (gnd) to set the output voltage to a value higher than 0.7 v. the temperature stability of the resistor should be 100 ppm/ (or better). the setpoint range for t he output voltage is from 0.7v to 3.6v. if left open circuit, the output voltage defaults to its lowest value. for further information, on output voltage adjustment see the related application note. the specification table gives the preferred resistor values for a number of standard output voltages. 13 turbo trans this input pin adjusts the transient response of the regu lator. to activate the turbo trans tm feature, a 1%, 50mw resistor must be connected between this pin and pin 10 (+sense) very close to the module. for a given value of output capacitance, a reducti on in peak output voltage deviation is achieved by using this feature. if unused, this pin must be left open-circuit. external capacitance must never be connected to this pin. the resistance requirement can be selected from the turbo trans tm resistor table in the application information section. 14 track this is an analog control input that enables the output voltage to follow an external voltage. this pin becomes active typically 20 ms after the input voltage has been applied, and allows direct control of the output voltage from 0 v up to the nominal set-point voltage. within the control voltage is raised above this range, the module regulates at its set-point voltage. the features allows the output voltage to rise simultaneously with other modules powered from the same input bus. if unused, this input should be connected to v i . note: due to the undervoltage lockout feature, the output of the module cannot follow its own input voltage during power up. for more information, see the related application note. e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 32 mechanical information ( surface mount versions ) e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 33 mechanical information ( throu g h hole mount version ) e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 34 ericsson internal prod. spec. mech. 1 (4) prepared (also subject responsible if other) no. epanhon 5/1301-bmr 656 uen approved checked date rev reference sec/d (julia you) see 1 2007-06-25 b soldering information - surface mounting the surface mount version of the product is intended for convection or vapor phase reflow snpb or pb-free processes. to achieve a good and reliable soldering result, make sure to follow the recommendations from the solder paste supplier, to use state-of-the-art reflow equipment and reflow profiling techniques as well as the following guidelines. a no-clean flux is recommended to avoid entrapment of cleaning fluids in cavities inside the product or between the product and the host board. the cleanin g residues ma y affect long time reliability and isolation voltage. minimum pin temperature recommendations pin number 5 is chosen as reference location for the minimum pin temperature recommendations since this will likely be the coolest solder joint during the reflow process. pin 5 for measurement of minimum solder joint temperature, t pin pin 2 for measurement of maximum peak product reflow temperature, t p snpb solder processes for snpb solder processes, a pin temperature (t pin ) in excess of the solder melting temperature, (t l , +183c for sn63/pb37) for more than 30 seconds, and a peak temperature of +210c is recommended to ensure a reliable solder joint. lead-free (pb-free) solder processes for pb-free solder processes, a pin temperature (t pin ) in excess of the solder melting temperature (t l , +217 to +221c for sn/ag/cu solder alloys) for more than 30 seconds, and a peak temperature of +235c on all solder joints is recommended to ensure a reliable solder joint. peak product temperature requirements pin 2 is chosen as reference location for the maximum (peak) allowed product temperature (t p ) since this will likely be the warmest part of the product during the reflow process. to avoid dama g e or performance de g radation of the product, the reflow profile should be optimized to avoid excessive heating. a sufficientl y extended preheat time is recommended to ensure an even temperature across the host pcb, for both small and large devices. to reduce the risk of excessive heating is also recommended to reduce the time in the reflow zone as much as possible. snpb solder processes for snpb solder processes, the product is qualified for msl 1 according to ipc/jedec standard j-std-020c. during reflow, t p must not exceed +225c at any time. lead-free (pb-free) solder processes for pb-free solder processes, the product is qualified for msl 3 according to ipc/jedec standard j-std-020c. during reflow, t p must not exceed +260c at any time. 25 c time temperature ramp-down (cooling) ramp-up reflow preheat time 25 c to pea k t p t l reflow process specifications sn/pb eutectic pb-free average ramp-up rate 3 c/s max 3 c/s max solder melting temperature (typical) t l +183c +221c minimum time above t l 30 s 30 s minimum pin temperature t pin +210c +235c peak product temperature t p +225c +260c average ramp-down rate 6c/s max 6c/s max time 25 c to peak 6 minutes max 8 minutes max e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 35 ericsson internal prod. spec. mech. 2 (4) prepared (also subject responsible if other) no. epanhon 5/1301-bmr 656 uen approved checked date rev reference sec/d (julia you) see 1 2007-06-25 b soldering information ? through hole mounting the through hole mount version of the product is intended for manual or wave soldering. when wave soldering is used, the temperature on the pins is specified to maximum 270 c for maximum 10 seconds. a maximum preheat rate of 4c/s and a temperature of max of +150c is suggested. when soldering by hand, care should be taken to avoid direct contact between the hot soldering iron tip and the pins for more than a few seconds in order to prevent overheating. a no-clean flux is recommended to avoid entrapment of cleaning fluids in cavities inside the product or between the product and the host board. the cleanin g residues ma y affect long time reliability and isolation voltage. delivery package information the th version products are delivered in antistatic trays. the smd version products are delivered in antistatic trays and antistatic carrier tape (eia 481 standard). tray specifications material antistatic pet surface resistance 10 6 < ohm/square < 10 12 tray capacity 35 products/tray tray thickness 13 mm [0.512 inch] box capacity 175 products ( 5 full trays/box) bakability the tray is not bakable. carrier tape specifications material antistatic ps surface resistance 10 7 < ohm/square < 10 12 bakability the tape is not bakable. tape width 56 mm [2.205 inch] pocket pitch 24 mm [0.945 inch] pocket depth 9.57 mm [0.377 inch] reel diameter 381 mm [15 inch] reel capacity 250 products /reel non-dry pack information the through hole mount version of product is delivered in non-dry packing trays. the lead (pb) surface mount version of product is delivered in non-dry packing trays or tape & reel. dry pack information the lead free (pb-free) surface mount version of the product is delivered in trays or tape & reel. these inner shipment containers are dry packed in standard moisture barrier bags according to ipc/jedec standard j-std-033 (handling, packing, shipping and use of moisture/reflow sensitivity surface mount devices). using products in high temperature pb-free soldering processes requires dry pack storage and handling. in case the products have been stored in an uncontrolled environment and no longer can be considered dry, the modules must be baked ac cording to j-std-033. e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 36 ericsson internal prod. spec. mech. 3 (4) prepared (also subject responsible if other) no. epanhon 5/1301-bmr 656 uen approved checked date rev reference sec/d (julia you) see 1 2007-06-25 b product qualification specification characteristics external visual inspection ipc-a-610 change of temperature (temperature cycling) iec 60068-2-14 na temperature range number of cycles dwell/transfer time -40 to +100 c 1000 15 min/0-1 min cold (in operation) iec 60068-2-1 ad temperature t a duration -45c 72 h damp heat iec 60068-2-67 cy temperature humidity duration +85 c 85 % rh 1000 hours dry heat iec 60068-2-2 bd temperature duration +125 c 1000 h immersion in cleaning so lvents iec 60068-2-45 xa method 2 water glycol ether +55 c +35 c mechanical shock iec 60068-2-27 e a peak acceleration duration 100 g 6 ms moisture reflow sensitivity 1 j-std-020c level 1 (snpb-eutectic) level 3 (pb free) 225 c 260 c operational life test mil-std-202g method 108a duration 1000 h resistance to soldering heat 2 iec 60068-2-20 tb method 1a solder temperature duration 270 c 10-13 s robustness of terminations iec 60068-2-21 test ua1 iec 60068-2-21 test ue1 through hole mount products surface mount products all leads all leads solderability iec 60068-2-58 test td 1 iec 60068-2-20 test ta 2 preconditioning temperature, snpb eutectic temperature, pb-free preconditioning temperature, snpb eutectic temperature, pb-free 150 c dry bake 16 h 215 c 235 c steam ageing 235 c 245 c vibration, broad band random ie c 60068-2-64 fh, method 1 frequency spectral density duration 10 to 500 hz 0.07 g 2 /hz 10 min in each perpendicular direction note 1: only for products intended for reflow soldering (surface mount products) note 2: only for products intended for wa ve soldering (plated through hole products) e pmn 8000 series dc/dc regulator, input 5.5-14 v, output 30 a/108 w en/lzt 146 387 r1c oct 2011 ? ericsson power modules ab technical speci? cation 37 mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: ericsson power modules: ? pmn8118uwp? PMN8118UWS? PMN8118UWSr |
Price & Availability of PMN8118UWS
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |